omron wrist bp monitor manual

The Omron Wrist Blood Pressure Monitor is a clinically validated, automatic device for convenient at-home blood pressure and pulse rate monitoring. It features IntelliSense technology for comfortable inflation, a large LCD display with date/time, hypertension indicator, irregular heartbeat detection, memory storage for multiple users, and a compact, portable design. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Main Unit (Monitor), Wrist Cuff, Storage Case, Instruction Manual, and Batteries.

Device Components

Unpack and verify all items are present.

1. Main Monitor Unit: Contains the display, buttons, and air pump.
2. Wrist Cuff: With Velcro closure and air tube connector.
3. Storage Case: For protecting the device when not in use.
4. Instruction Manual: This guide.
5. Batteries: Typically 2 AAA batteries (included).

WARNING! Do not use the monitor if any parts are damaged. Keep small parts away from children.

Initial Setup & Preparation

Before first use, install batteries and set the date/time.

1. Insert Batteries: Open the battery compartment on the back, insert 2 AAA batteries as indicated.
2. Set Date/Time: Press the MEMORY button while holding the START/STOP button to enter setting mode. Use START/STOP to adjust values and MEMORY to confirm.
3. Prepare for Measurement: Rest for 5 minutes in a seated position. Avoid caffeine, exercise, and smoking for 30 minutes prior.
4. Positioning: Place the cuff on your left wrist (unless specified otherwise) with the monitor face-up. Position so the cuff edge is 0.5-1 inch (1-2 cm) from your hand.

CAUTION! Ensure the cuff is at heart level during measurement for accurate readings.

Specifications

• Measurement Method: Oscillometric (automatic inflation/deflation).
• Measurement Range: Pressure: 0 - 299 mmHg, Pulse: 40 - 180 beats/minute.
• Accuracy: Pressure: ±3 mmHg, Pulse: ±5% of reading.
• Memory: 100 readings x 2 users.
• Cuff Size: Fits wrist circumference 5.3" - 8.5" (13.5 - 21.5 cm).
• Power Source: 2 AAA batteries (DC 3.0V).
• Battery Life: Approximately 300 measurements.
• Operating Conditions: 50°F to 104°F (10°C to 40°C), 30% to 85% relative humidity.
• Display: Liquid Crystal Display (LCD).
• Weight: Approximately 3.5 oz (100 g) (without batteries).

Taking a Measurement

Follow these steps precisely for an accurate reading.

1. Sit comfortably with feet flat on the floor and back supported.
2. Place the cuff on your bare left wrist. Secure it snugly but not too tight.
3. Rest your elbow on a table and raise your hand so the cuff is at heart level. Relax your hand.
4. Press the START/STOP button. The cuff will inflate automatically.
5. Remain still and quiet until the measurement is complete and the cuff deflates.
6. Your systolic/diastolic pressure and pulse rate will be displayed.
7. The monitor will automatically store the reading (if user is selected) and power off after 1 minute.

Tip: Take measurements at the same time each day for consistent tracking.

Understanding the Display

The LCD shows icons and values. Key symbols:

Memory Function

To store and review readings:

1. Select User: Press the MEMORY button before turning the monitor on to select User 1 or User 2.
2. Automatic Storage: After a measurement, the reading is saved to the selected user's memory with date/time.
3. Review Memory: Press the MEMORY button after turning the monitor on. Use START/STOP to scroll through readings.
4. View Average: While reviewing memory, the average of the last 3 readings taken within 10 minutes is displayed.
5. Clear Memory: Hold the MEMORY button for 3 seconds while in memory mode to clear all readings for the selected user.

Note: Memory is retained even when batteries are removed.

Care & Maintenance

Proper care ensures longevity and accuracy.

• Clean the cuff with a soft, dry cloth. Do not wash or immerse in water.
• Clean the monitor body with a slightly damp cloth. Do not use alcohol or abrasive cleaners.
• Store the device in its case in a cool, dry place away from direct sunlight, extreme temperatures, and humidity.
• Avoid dropping or subjecting the monitor to strong impacts.
• Do not disassemble or attempt to repair the unit yourself.

CAUTION! Never use the monitor near flammable gases or in oxygen-rich environments.

Battery Information

Using and replacing batteries.

1. Use only 2 AAA alkaline batteries.
2. When the low battery icon appears, replace both batteries promptly.
3. Remove batteries if the monitor will not be used for an extended period (3 months or more).
4. Dispose of used batteries according to local regulations.

WARNING! Do not mix old and new batteries or different types of batteries. This may cause leakage or malfunction.

Regulatory & Warranty

This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that it does not cause harmful interference. This product meets the applicable standards for medical devices. Manufactured for Omron Healthcare, Inc. For warranty service, contact Omron at 1-800-634-4350 or visit www.omronhealthcare.com. Warranty period is typically 5 years from date of purchase.

Troubleshooting

Reset: Remove batteries for 1 minute, then reinstall to reset the monitor.

Service: 1-800-634-4350; www.omronhealthcare.com