Omron Intellisense Wrist Manual

The Omron Intellisense Wrist is a clinically validated, automatic blood pressure monitor designed for convenient wrist measurement. It features Intellisense technology for accurate readings, a large LCD display, memory storage for multiple users, irregular heartbeat detection, hypertension indicator, and comfortable cuff. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Wrist unit with LCD display, Wrist Cuff, Storage Case, Instruction Manual, Batteries.

Safety Precautions

Read all instructions before use. For personal use only.

1. Consult your physician before use if you have arrhythmia, poor circulation, or other conditions.
2. Do not use on infants, children, or persons unable to express themselves.
3. Do not use during or immediately after physical exercise, bathing, eating, or drinking alcohol/caffeine.
4. Ensure wrist cuff is at heart level during measurement for accurate results.

WARNING! This device is not a substitute for professional medical diagnosis. Do not adjust medication based solely on readings.

Device Components

Identify all parts before use.

1. Main Unit: Contains LCD display, buttons, and internal pump.
2. Wrist Cuff: Pre-formed cuff with Velcro closure.
3. Storage Case: For protecting device when not in use.
4. Batteries: Two AAA batteries (included).
5. Instruction Manual: This guide.

CAUTION! Do not disassemble the device. Keep away from children.

Specifications

• Measurement Method: Oscillometric (wrist).
• Measurement Range: Pressure: 0-299 mmHg, Pulse: 40-180 beats/min.
• Accuracy: Pressure: ±3 mmHg, Pulse: ±5% of reading.
• Memory: 14 readings with date and time.
• Cuff Circumference: Fits wrists 5.3" to 8.5" (13.5-21.5 cm).
• Power Source: Two AAA 1.5V batteries (DC).
• Battery Life: Approximately 300 measurements.
• Operating Conditions: Temperature: 50°F to 104°F (10°C to 40°C), Humidity: 30% to 85% RH.
• Dimensions: Main unit: 2.8" x 3.9" x 1.2" (72 x 100 x 31 mm).
• Weight: Approximately 3.5 oz (100 g) without batteries.

Initial Setup

Prepare device for first use.

1. Insert batteries: Open battery compartment, insert two AAA batteries observing polarity.
2. Set date and time: Press and hold MEMORY button for 3 seconds, use START/STOP to adjust.
3. Apply cuff correctly: Place on left wrist (unless instructed otherwise), 0.5-1 inch above wrist bone.
4. Positioning: Sit comfortably, rest elbow on table, raise wrist to heart level.

Tip: Rest for 5 minutes before first measurement. Avoid talking or moving during measurement.

Taking a Measurement

Follow these steps for accurate readings.

1. Sit comfortably with back straight and feet flat on floor.
2. Apply cuff to left wrist as described in Initial Setup.
3. Press START/STOP button. Cuff will inflate automatically.
4. Remain still and quiet until measurement is complete (cuff deflates).
5. Readings display: Systolic, diastolic, pulse, and any indicators.
6. Device automatically stores reading (if memory available).
7. Press START/STOP again to turn off display, or wait for auto power-off.

WARNING! Do not inflate cuff without proper positioning. Excessive pressure may cause discomfort.

Memory Function

Review and manage stored readings.

1. Press MEMORY button to display most recent reading.
2. Press MEMORY repeatedly to scroll through stored readings (newest to oldest).
3. Each reading shows systolic/diastolic pressure, pulse, date, and time.
4. Memory full: Oldest reading is overwritten when 15th reading is taken.
5. Clear memory: Remove batteries for 10 seconds (erases all data).

Note: Memory is for single user only. For multiple users, record readings separately.

Understanding Results

Interpret display symbols and readings.

Tip: Take measurements at same time daily for consistent tracking. Share results with your physician.

Care & Maintenance

Proper care ensures accuracy and longevity.

1. Clean cuff with mild soap and damp cloth; air dry completely.
2. Wipe main unit with dry, soft cloth.
3. Do not immerse in water or use abrasive cleaners.
4. Store in provided case in cool, dry place away from direct sunlight.
5. Replace batteries when low battery symbol appears.
6. Remove batteries if not using for extended period.

CAUTION! Do not sterilize with autoclave, ethylene oxide gas, or radiation. Avoid extreme temperatures.

Regulatory Information

FDA Cleared: KXXXXXX. Manufactured for Omron Healthcare, Inc. CE Mark: Complies with Medical Device Directive 93/42/EEC. Copyright © Omron Healthcare, Inc. All rights reserved. For support, visit www.omronhealthcare.com or contact 1-800-634-4350.

Troubleshooting

Reset: Remove batteries for 10 seconds to reset device.

Service: 1-800-634-4350; www.omronhealthcare.com