Omron Intellisense BP652 Manual

The Omron Intellisense BP652 is an automatic upper arm blood pressure monitor featuring IntelliSense technology for accurate and comfortable readings, irregular heartbeat detection, hypertension indicator, body movement detection, memory storage for multiple users, and a large LCD display with backlight. It is designed for home use and provides clinically validated measurements. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Main unit, Upper Arm Cuff, AC Adapter, Instruction Manual, Storage Case.

Safety Information

Read all instructions before use. For accurate measurements and safe operation.

1. Do not use on infants, children, or persons unable to express themselves.
2. Consult your physician before use if you have arrhythmia, other heart problems, or are pregnant.
3. Do not use the monitor on an injured arm or if you have an IV line or shunt.
4. Do not inflate the cuff when it is not wrapped around your arm.
5. Keep the monitor away from children and pets.

WARNING! This device is not a substitute for professional medical diagnosis. Consult your doctor for interpretation of readings.

Package Contents

Unpack and verify all items are present.

• Omron Intellisense BP652 Main Unit
• Comfort-Fit Upper Arm Cuff (22-42 cm)
• AC Adapter
• Instruction Manual
• Storage Case
• 4 x AA Batteries (may be included depending on region)

CAUTION! Do not use if any components are damaged. Contact customer service.

Device Overview

Front Panel: START/STOP Button, Memory Button, User Selection Button (1/2), Power Button, LCD Display.

Display Symbols: Systolic Pressure, Diastolic Pressure, Pulse Rate, Irregular Heartbeat Symbol, Hypertension Indicator, Body Movement Symbol, User Indicator, Memory Indicator, Date/Time, Battery Level, Cuff Wrap Guide, WHO Classification Bar.

Rear: Cuff Port, AC Adapter Jack, Battery Compartment.

Initial Setup

Power on the device and configure basic settings.

1. Insert Batteries: Open battery compartment, insert 4 AA batteries observing polarity.
2. Connect Cuff: Plug cuff tube firmly into the cuff port on the side of the monitor.
3. Set Date & Time: Press and hold the Memory button for 3 seconds to enter setting mode. Use START/STOP to adjust values, Memory to confirm.
4. Select User: Press the User button to select User 1 or User 2 for memory storage.

Tip: For first-time use, allow the monitor to sit at room temperature for 30 minutes.

Taking a Measurement

For the most accurate results, follow these steps carefully.

1. Rest quietly for 5 minutes before measuring.
2. Sit on a chair with feet flat on the floor and back supported.
3. Wrap the cuff on your bare upper arm 1-2 cm above elbow. Ensure air tube is centered over inner arm.
4. Position cuff at heart level. Rest arm on a table.
5. Press START/STOP. The cuff will inflate automatically.
6. Remain still and quiet until measurement is complete and cuff deflates.
7. Read your systolic, diastolic, and pulse rate on the display.
8. Press START/STOP to turn off, or it will power off automatically.

WARNING! Do not move or talk during measurement. Ensure cuff is not too tight or loose.

Understanding the Display

After measurement, the display shows:

• Systolic Pressure: Top number (e.g., 120).
• Diastolic Pressure: Bottom number (e.g., 80).
• Pulse Rate: Beats per minute.
• Irregular Heartbeat Symbol: Flashes if an irregular rhythm is detected.
• Hypertension Indicator: Appears if systolic ≥135 or diastolic ≥85.
• Body Movement Symbol: Appears if excessive movement was detected.
• WHO Bar: Color bar indicates optimal (green), normal (yellow), or high (red) range.

Memory Function

Stores up to 100 readings total (50 per user).

1. To view memory: Press Memory button. Display shows average of last 3 readings for selected user.
2. To scroll through readings: Press Memory button repeatedly to cycle through individual readings with date/time.
3. To clear memory: While in memory mode, press and hold Memory button for 3 seconds until "CLr" appears.
4. User selection: Press User button to switch between User 1 and User 2 memory.

Note: Memory is retained when batteries are removed.

Care & Maintenance

Unplug adapter and remove batteries before cleaning.

1. Clean monitor and cuff with a soft, dry cloth. Do not use solvents or abrasives.
2. Do not immerse in water or other liquids.
3. Store in the provided case in a cool, dry place away from direct sunlight.
4. Replace batteries when low battery icon appears.
5. Do not disassemble or attempt to repair the unit.

CAUTION! Do not wash the cuff. Avoid bending the air tube excessively.

Specifications

• Measurement Method: Oscillometric
• Pressure Range: 0-299 mmHg
• Pulse Range: 40-180 beats/minute
• Accuracy: Pressure: ±3 mmHg, Pulse: ±5% of reading
• Memory: 100 readings for 2 users
• Cuff Size: 22-42 cm (upper arm circumference)
• Power Source: 4 x AA batteries or AC adapter (included)
• Display: LCD with backlight
• Operating Conditions: 10°C to 40°C, 15% to 85% RH
• Dimensions: Approx. 123mm (W) x 85mm (H) x 141mm (D)
• Weight: Approx. 340g (without batteries)

Troubleshooting

Reset: Remove batteries and AC adapter for 1 minute, then reinsert.

Service: For repairs, contact authorized Omron service center. Do not open the unit.