Omron Blood Pressure Manual

The Omron Blood Pressure Monitor is a reliable, clinically validated device for accurate at-home blood pressure measurement. It features IntelliSense technology for comfortable inflation, hypertension detection indicators, irregular heartbeat detection, memory storage for multiple users, and a large, easy-to-read display. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Main unit with display, Arm cuff, AC adapter port, Memory buttons, START/STOP button, User selection buttons.

Safety Precautions

Read all instructions before use. Consult your physician for interpretation of readings.

1. Do not use on infants, small children, or persons unable to express themselves.
2. Do not use during vehicle operation or if you suspect arrhythmia.
3. Avoid measurement on arm with IV drip, injury, or arteriovenous shunt.
4. Wait at least 1 hour after exercise, bathing, eating, or consuming caffeine/alcohol.
5. Remain still and quiet during measurement; do not talk or move arm.

WARNING! This device is for home monitoring only, not for diagnosis. Always follow your doctor's advice.

Device Components

Unpack and verify all components are present.

1. Main Unit: Contains display, control buttons, and internal pump.
2. Arm Cuff: Pre-formed fabric cuff with Velcro closure and air tube.
3. AC Adapter Port: For optional external power (Model EA11A).
4. Battery Compartment: Holds 4 AA batteries (included for initial use).
5. Storage Case: For protecting device when not in use.

CAUTION! Do not bend or kink the air tube. Keep cuff clean and dry.

Initial Setup

Prepare device for first use.

1. Insert batteries: Open compartment, insert 4 AA batteries observing polarity.
2. Set date and time: Press and hold CLOCK button, use UP/DOWN to adjust.
3. Attach cuff: Connect cuff tube to main unit until it clicks securely.
4. Select user: Press USER 1 or USER 2 button to choose memory profile.
5. Test operation: Without wearing cuff, press START to verify inflation/deflation.

Tip: For most accurate results, use at the same time each day in a quiet environment.

Taking a Measurement

Follow these steps for accurate readings.

1. Sit comfortably with back supported and feet flat on floor for 5 minutes.
2. Wrap cuff on bare upper arm 1-2 cm above elbow, aligning artery marker with brachial artery.
3. Secure cuff snugly; tube should run down center of arm toward palm.
4. Rest arm on table with cuff at heart level; palm facing upward.
5. Press START button; cuff will inflate automatically.
6. Remain still and quiet until measurement completes and cuff deflates.
7. Read results on display; note systolic, diastolic, and pulse readings.
8. Press STOP to turn off display, or wait 1 minute for auto power-off.

WARNING! Do not inflate cuff when not wrapped on arm. Excessive pressure may cause injury.

Understanding Results

• Systolic Pressure: Top number - pressure when heart beats.
• Diastolic Pressure: Bottom number - pressure between beats.
• Pulse: Heart rate in beats per minute.
• Hypertension Indicator: Heart symbol flashes if reading exceeds 135/85 mmHg.
• Irregular Heartbeat Symbol: Appears if irregular rhythm detected during measurement.
• Movement Error: Hand symbol appears if excessive movement detected.
• Cuff Error: Appears if cuff is improperly placed or too loose.

Note: Single readings may vary. Track trends over time for meaningful data.

Memory Function

Device stores readings for two users.

1. Select user: Press USER 1 or USER 2 before measurement.
2. View memory: Press MEMORY button to scroll through stored readings.
3. Average reading: Automatically calculates average of last 3 readings taken within 10 minutes.
4. Clear memory: While in memory mode, press and hold MEMORY for 3 seconds to erase all readings for selected user.
5. Date/Time stamp: Each reading includes date and time of measurement.

Tip: Record readings in a log to share with your healthcare provider.

Maintenance & Care

Proper care ensures accurate measurements and long device life.

1. Clean cuff with mild soap and damp cloth only; do not immerse in water.
2. Wipe main unit with dry, soft cloth; never use solvents or abrasives.
3. Store in case provided; keep in cool, dry place away from direct sunlight.
4. Remove batteries if device will not be used for 3 months or longer.
5. Replace cuff if Velcro no longer holds securely or fabric shows wear.

CAUTION! Do not disassemble device. No user-serviceable parts inside.

Battery Replacement

Replace batteries when low battery symbol appears.

1. Press battery compartment latch and remove cover.
2. Remove old batteries, observing polarity orientation.
3. Insert 4 new AA alkaline batteries with correct polarity (+/-).
4. Replace cover until it clicks securely.
5. Test device with a measurement to ensure proper operation.

Note: Battery life approximately 300 measurements. Use optional AC adapter for extended use.

Specifications

• Measurement Method: Oscillometric
• Pressure Range: 0-299 mmHg
• Pulse Range: 40-180 beats/minute
• Accuracy: Pressure: ±3 mmHg, Pulse: ±5% of reading
• Memory: 100 readings x 2 users
• Cuff Circumference: 22-42 cm (9-17 inches)
• Power Source: 4 AA batteries or AC adapter (optional)
• Battery Life: Approx. 300 measurements
• Dimensions: 123mm (W) x 85mm (H) x 141mm (D)
• Weight: Approx. 400g (without batteries)
• Operating Conditions: 10°C to 40°C, 30-85% humidity

Troubleshooting

Reset: Remove batteries for 1 minute to reset device to factory settings.

Service: For technical support, contact Omron Healthcare at 1-800-634-4350 or visit www.omronhealthcare.com